ENGINE 450G 550G 650G
Type................................................John Deere 4045T with altitude- John Deere 4045T with altitude- John Deere 4045T with altitude-
compensating turbocharger; compensating turbocharger compensating turbocharger
John Deere 4045D naturally
aspirated (direct drive only)
Rated power ...................................70 SAE net hp (52 kW) / 73 SAE 80 SAE net hp (59.5 kW) / 83 SAE 90 SAE net hp (67.5 kW);
gross hp (54.5 kW) @ 2,100 rpm gross hp (62 kW) @ 2,100 rpm 650G DD – 95 SAE gross hp (71 kW);
650G TC – 99 SAE gross hp (74 kW)
@ 2,100 rpm
Drawbar..........................................51 hp (38 kW) 58 hp (43 kW) 66 hp (49 kW)
Cylinders........................................4 4 4
Displacement .................................276 cu. in. (4.524 L) 276 cu. in. (4.524 L) 276 cu. in. (4.524 L)
Fuel consumption, typical .............1.5 to 2.3 gal./hr. (4.9 to 8.7 L/h) 1.6 to 2.4 gal./hr. (6.1 to 9.1 L/h) 1.8 to 2.8 gal./hr. (6.8 to 10.6 L/h)
Maximum net torque.....................228 lb.-ft. (309 Nm) @ 1,300 rpm 260 lb.-ft. (353 Nm) @ 1,300 rpm 293 lb.-ft. (397 Nm) @ 1,300 rpm
Lubrication.....................................pressure system with full-flow spin- pressure system with full-flow spin- pressure system with full-flow spin-
on filter and oil-to-water cooler on filter and oil-to-water cooler on filter and oil-to-water cooler
Air cleaner ......................................dual stage dry type with safety dual stage dry type with safety dual stage dry type with safety
element, precleaner, and under- element, precleaner, and under- element, precleaner, and under-
hood restriction indicator hood restriction indicator hood restriction indicator
Electrical system.............................12 volt with 65-amp alternator 12 volt with 65-amp alternator 12 volt with 65-amp alternator
Cooling fan ....................................blower blower blower
TRANSMISSION
full power shift, Dura-Shift with torque converter or direct drive; change gears easily using the engine decelerator
and power shift
450G TC 450G DD 550G TC 550G DD 650G TC 650G DD
mph (km/h) mph (km/h) mph (km/h) mph (km/h) mph (km/h) mph (km/h)
Maximum travel speeds
1st Forward ...............................2.30 (3.70) 1.45 (2.33) 2.31 (3.72) 1.54 (2.48) 2.28 (3.67) 1.51 (2.43)
2nd Forward .............................3.31 (5.33) 2.41 (3.88) 3.32 (5.34) 2.58 (4.15) 3.28 (5.28) 2.53 (4.07)
3rd Forward ..............................4.11 (6.61) 3.29 (5.29) 4.09 (6.58) 3.28 (5.28) 4.09 (6.58) 3.34 (5.38)
4th Forward ..............................5.91 (9.51) 5.51 (8.87) 5.88 (9.46) 5.49 (8.84) 5.87 (9.45) 5.59 (9.00)
1st Reverse ................................2.50 (4.02) 1.60 (2.57) 2.50 (4.02) 1.70 (2.74) 2.46 (3.96) 1.67 (2.69)
2nd Reverse...............................3.58 (5.76) 2.67 (4.30) 3.59 (5.78) 2.85 (4.59) 3.54 (5.70) 2.80 (4.51)
3rd Reverse................................4.47 (7.19) 3.63 (5.84) 4.36 (7.02) 3.62 (5.83) 4.30 (6.92) 3.70 (5.95)
4th Reverse ...............................5.93 (9.54) 6.09 (9.80) 5.86 (9.43) 6.06 (9.75) 5.80 (9.33) 6.19 (9.96)
FINAL DRIVES
large heavy-duty final drive assemblies attach directly to the transverse case and are isolated from the track
frame to keep final drives from being adversely affected by shock loads; 450G is single reduction, 550G and
650G are double
STEERING/BRAKES
oil-cooled and modulated steering system; multiple wet-disk steering clutches and wet-band steering brakes are
pressure lubricated and located at the rear of the machine for easy servicing
AUTOMATIC PARK BRAKE
exclusive safety feature engages whenever the engine stops, preventing machine operation, which eliminates
brake damage
HYDRAULIC SYSTEM
System ............................................open center open center open center
Pressure, main relief.......................2,750 psi (18 961 kPa) 2,750 psi (18 961 kPa) 2,750 psi (18 961 kPa)
Pump..............................................gear gear gear
Flow................................................17 gpm (64 L/min.) @ 2,100 rpm 17 gpm (64 L/min.) @ 2,100 rpm 17 gpm (64 L/min.) @ 2,100 rpm
Filter, return oil..............................10 micron 10 micron 10 micron
Control...........................................T-bar three function T-bar three function T-bar three function
Cylinders........................................heat-treated, chrome-plated, heat-treated, chrome-plated, heat-treated, chrome-plated,
polished cylinder rods with hard- polished cylinder rods with hard- polished cylinder rods with hard-
ened steel (replaceable bushings) ened steel (replaceable bushings) ened steel (replaceable bushings)
pivot pins pivot pins pivot pins
UNDERCARRIAGE
John Deere Dura-Trax
TM
features large deep-heat-treated components; pins and bushings are sealed for life;
rollers and idlers are permanently sealed and lubricated; full-length track frame covers reduce material buildup
and ease cleaning
Chain
Standard....................................sealed sealed sealed
Optional....................................sealed and lubricated sealed and lubricated sealed and lubricated
Pitch..........................................6.29 in. (159.8 mm) 6.29 in. (159.8 mm) 6.73 in. (171.1 mm)
SPECIFICATIONS
16
97-09 English version 2/25/00 8:55 AM Page 16
UNDERCARRIAGE (continued) 450G 550G 650G
STANDARD TRACK
Grouser .....................................16 in. (406 mm) closed center not available 18 in. (457 mm) closed center
single bar single bar
Ground contact area.................2,432 sq. in. (15 690 cm
2
) 3,082 sq. in. (19 884 cm
2
)
Ground pressure
Torque converter.................6.55 psi (45.2 kPa) 6.01 psi (41.4 kPa)
Direct drive..........................6.47 psi (44.6 kPa) 5.94 psi (41.0 kPa)
Overall width over track...........73 in. (1854 mm) 79 in. (2007 mm)
Track shoes, each side ..............37 38
Length of track on ground .......76 in. (1930 mm) 85.6 in. (2174 mm)
Track gauge...............................57 in. (1450 mm) 61 in. (1550 mm)
Track rollers ..............................5 6
Adjustment ...............................hydraulic with hinged dirt cover hydraulic with hinged dirt cover
LONG TRACK
Grouser .....................................16 in. (406 mm) closed center 18 in. (457 mm) closed center not available
single bar single bar
Ground contact area.................2,733 sq. in. (17 632 cm
2
) 2,732 sq. in. (19 834 cm
2
)
Ground pressure
Torque converter.................6.04 psi (41.7 kPa) 6.47 psi (44.7 kPa)
Direct drive..........................5.97 psi (41.1 kPa) 6.4 psi (44.1 kPa)
Overall width over track...........73 in. (1854 mm) 79 in. (2007 mm)
Track shoes, each side ..............40 40
Length of track on ground .......85 in. (2160 mm) 85.4 in. (2169 mm)
Track gauge...............................57 in. (1450 mm) 61 in. (1550 mm)
Track rollers ..............................6 6
Adjustment ...............................hydraulic with hinged dirt cover hydraulic with hinged dirt cover
LOW GROUND PRESSURE
Grouser .....................................24 in. (610 mm) closed center 24 in. (610 mm) closed center 24 in. (610 mm) closed center
single bar single bar single bar
Ground contact area.................4,099 sq. in. (26 445 cm
2
) 4,099 sq. in. (26 447 cm
2
) 4,109 sq. in. (26 510 cm
2
)
Ground pressure
Torque converter.................4.25 psi (29.3 kPa) 4.52 psi (31.2 kPa) 4.70 psi (32.4 kPa)
Direct drive..........................4.20 psi (29.0 kPa) 4.47 psi (30.8 kPa) 4.65 psi (32.1 kPa)
Grouser ...................................................................................................................................................................26 in. (660 mm) closed center
single bar
Ground contact area ..............................................................................................................................................4,451 sq. in. (28 717 cm
2
)
Ground pressure
Torque converter ..............................................................................................................................................4.45 psi (30.7 kPa)
Direct drive .......................................................................................................................................................4.41 psi (30.4 kPa)
Overall width over track...........93 in. (2362 mm) 93 in. (2362 mm) 93 in. (2362 mm)
Track shoes, each side ..............40 40 38
Length of track on ground .......85 in. (2160 mm) 85.4 in. (2169 mm) 85.6 in. (2174 mm)
Track gauge...............................69 in. (1750 mm) 69 in. (1750 mm) 69 in. (1750 mm)
Track rollers ..............................6 6 6
Adjustment ...............................hydraulic with hinged dirt cover hydraulic with hinged dirt cover hydraulic with hinged dirt cover
CAPACITIES (U.S.)
Fuel tank with lockable cap ...........41 gal. (155.2 L) 41 gal. (155.2 L) 41 gal. (155.2 L)
Cooling system with coolant
recovery tank ............................18 qt. (17.0 L) 18 qt. (17.0 L) 18 qt. (17.0 L)
Engine oil including spin-on filter ....9 qt. (8.5 L) 13 qt. (12.3 L) 13 qt. (12.3 L)
Transmission system including
spin-on filter in filter center
Torque converter ......................27 gal. (102 L) 27 gal. (102 L) 27 gal. (102 L)
Direct drive...............................27 gal. (102 L) 27 gal. (102 L) 27 gal. (102 L)
Final drive (each) ...........................7 qt. (6.6 L) 10 qt. (9.5 L) 10 qt. (9.5 L)
Hydraulic reservoir.........................10 gal. (37.8 L) 10 gal. (37.8 L) 10 gal. (37.8 L)
Hydraulic system including
vertical spin-on filter in
filter center ...............................14.6 gal. (55.3 L) 14.6 gal. (55.3 L) 15 gal. (56.8 L)
All capacities are for torque converter unless otherwise noted. All power train and hydraulic systems allow 45-degree maximum fore-aft, side-to-side
operation without modification.
SPECIFICATIONS
17
97-09 English version 2/25/00 8:55 AM Page 17
OPERATING WEIGHTS 450G 550G 650G
With standard equipment With standard equipment With standard equipment
450G TC 450G DD 550G TC 550G DD 650G TC 650G DD
lb. (kg) lb. (kg) lb. (kg) lb. (kg) lb. (kg) lb. (kg)
Standard track ................................15,932 (7243) 15,732 (7152) not available not available 18,510 (8414) 18,310 (8323)
Wide track......................................16,888 (7677) 16,688 (7586) not available not available not available not available
Long track ......................................16,510 (7505) 16,310 (7415) 17,683 (8038) 17,483 (7947) not available not available
Low ground pressure (LGP) ...........17,432 (7924) 17,232 (7833) 18,530 (8423) 18,330 (8332) 19,322 (8783) 19,122 (8692)
DIMENSIONS
A Overall height with ROPS
and cab...............................108 in. (2740 mm) 109 in. (2770 mm) 110 in. (2794 mm)
Overall height with low-
profile ROPS.......................103.3 in. (2624 mm) 104.3 in. (2649 mm) 105.3 in. (2675 mm)
B Overall length
Standard and wide tracks .....154.2 in. (3917 mm) 160 in. (4070 mm) 160 in. (4070 mm)
B'
Overall length
Long and low ground
pressure tracks ..............156.5 in. (3975 mm) 160 in. (4070 mm) 160 in. (4070 mm)
C Blade lift height.......................32.1 in. (815 mm) 34.1 in. (866 mm) 35.7 in. (906 mm)
D Digging depth .........................19.9 in. (504 mm) 18.1 in. (460 mm) 16.5 in. (420 mm)
E Blade cutting edge angle,
two position adjustable .....50 or 55 degrees 50 or 55 degrees 50 or 55 degrees
G-SERIES BLADE SPECS
STANDARD BLADE
F Width ......................................97 in. (2464 mm) 105 in. (2667 mm) 105 in. (2667 mm)
G Height......................................32.6 in. (827 mm) 33.3 in. (847 mm) 35.4 in. (898 mm)
SAE capacity ............................2.0 cu. yd. (1.5 m
3
) 2.3 cu. yd. (1.7 m
3
) 2.5 cu. yd. (1.9 m
3
)
H Blade angle ..............................25 degrees 25 degrees 25 degrees
I Angled width...........................87.8 in. (2230 mm) 95.1 in. (2415 mm) 95.1 in. (2415 mm)
J Tilt ...........................................13.0 in. (330 mm) 14.1 in. (357 mm) 13.5 in. (343 mm)
NARROW BLADE (Will not cover standard track footprint when fully angled.)
F Width ......................................91 in. (2311 mm) 97 in. (2464 mm) 97 in. (2464 mm)
G Height......................................32.6 in. (827 mm) 32.6 in. (827 mm) 32.6 in. (827 mm)
SAE capacity ............................1.9 cu. yd. (1.4 m
3
) 2.0 cu. yd. (1.5 m
3
) 2.0 cu. yd. (1.5 m
3
)
H Blade angle ..............................25 degrees 25 degrees 25 degrees
I Angled width...........................82.4 in. (2093 mm) 87.8 in. (2230 mm) 87.8 in. (2230 mm)
J Tilt ...........................................12.2 in. (309 mm) 13.0 in. (330 mm) 12.5 in. (317 mm)
WIDE BLADES
F Width ......................................115 in. (2921 mm) 115 in. (2921 mm) 115 in. (2921 mm)
G Height......................................32.6 in. (827 mm) 32.6 in. (827 mm) 32.6 in. (827 mm)
SAE capacity ............................2.3 cu. yd. (1.8 m
3
) 2.3 cu. yd. (1.8 m
3
) 2.3 cu. yd. (1.8 m
3
)
H Blade angle ..............................23 degrees 23 degrees 23 degrees
I Angled width...........................105.7 in. (2686 mm) 105.7 in. (2686 mm) 105.7 in. (2686 mm)
J Tilt ...........................................15.4 in. (391 mm) 15.4 in. (391 mm) 14.8 in. (376 mm)
F Width ......................................121 in. (3073 mm) 121 in. (3073 mm) 121 in. (3073 mm)
G Height......................................32.6 in. (827 mm) 32.6 in. (827 mm) 32.6 in. (827 mm)
SAE capacity ............................2.5 cu. yd. (1.9 m
3
) 2.5 cu. yd. (1.9 m
3
) 2.5 cu. yd. (1.9 m
3
)
H Blade angle ..............................23 degrees 23 degrees 23 degrees
I Angled width...........................111.3 in. (2827 mm) 111.3 in. (2827 mm) 111.3 in. (2827 mm)
J Tilt ...........................................16.2 in. (411 mm) 16.2 in. (411 mm) 15.6 in. (396 mm)
F Width ....................................................................................................................................................................128 in. (3250 mm)
G Height ...................................................................................................................................................................32.6 in. (827 mm)
SAE capacity..........................................................................................................................................................2.6 cu. yd. (2.0 m
3
)
H Blade angle............................................................................................................................................................23 degrees
I Angled width ........................................................................................................................................................117.8 in. (2992 mm)
J Tilt.........................................................................................................................................................................16.6 in. (421 mm)
SPECIFICATIONS/DIMENSIONS
18
97-09 English version 2/25/00 8:55 AM Page 18
FORESTRY APPLICATION
available limb risers and screens for the rollover protective structure, John Deere-built 4000 Winch for versatile
skidding and clearing operations
K 4000 Winch length .................28.1 in. (713 mm)
DRAWBAR PULL
Crawler speed vs ground pull ................usable pull will depend on traction and weight of tractor
DIMENSIONS/SPECIFICATIONS
19
Ground Line
1.9 in. (49 mm)
single grouser height
Concrete Level
C
G
D
B
A
12 in. (305 mm)
B'
14.25 in. (362 mm)
Ground Clearance
E
6 in. (152 mm) Rigid Drawbar
11.5 in. (292 mm) Extended Drawbar
0123456
mph
160
140
120
100
80
60
40
20
DRAWBAR PULL x 1000 N (lb.)
SPEED
N
lb.
km/h
0123456789
32
28
24
20
16
12
8
4
TORQUE CONVERTER
DIRECT DRIVE
450G
0123456
mph
160
140
120
100
80
60
40
20
DRAWBAR PULL x 1000 N (lb.)
SPEED
N
lb.
km/h
0123456789
32
28
24
20
16
12
8
4
TORQUE CONVERTER
DIRECT DRIVE
650G
0123456
mph
160
140
120
100
80
60
40
20
DRAWBAR PULL x 1000 N (lb.)
SPEED
N
lb.
km/h
0123456789
32
28
24
20
16
12
8
4
TORQUE CONVERTER
DIRECT DRIVE
550G
K
J
F
H
H
I
Unit illustrated above is equipped with extended drawbar.
97-09 English version 2/25/00 8:55 AM Page 19
ADDITIONAL EQUIPMENT
DKA450G Litho in U.S.A. (97-09)
KEY:
●
Standard equipment
■
Optional or special equipment *See your John Deere dealer for further information.
20
Net engine power is with standard equipment including air cleaner, exhaust
system, alternator, and cooling fan, at standard conditions per SAE J1349 and
DIN 6270B, using No. 2-D fuel at 35 API gravity. No derating is required up to
5,000 ft. (1500 m) altitude for the 450G and up to 10,000 ft. (3050 m) altitude
for the 550G and 650G. Gross power is without cooling fan.
Specifications and design subject to change without notice. Wherever applicable, specifications are
in accordance with SAE standards. Except where otherwise noted, these specifications are based on
units with rollover protective structures, full fuel tanks, 175-lb. (79 kg) operators, and standard
equipment; 450G unit with 97-in. (2464 mm) PAT Blade for standard gauge or 121-in. (3073 mm)
PAT Blade for wide gauge; and 550G and 650G units with 105-in. (2667 mm) PAT Blade.
ENGINE
Coolant recovery tank
●●●
Enclosed safety fan guard
●●●
Conforms to SAE J1308
Engine coolant –34°F (–37°C)
●●●
Natural aspiration (direct drive only)
●
Oil-to-water engine oil cooler
●●●
Quick release fuel filter
●●●
Trash-resistant six-fin radiator
●●●
Underhood muffler with vertical
exhaust stack
●●●
Spark arrester:
Torque converter
●●●
Direct drive*
■ ●●
Heavy-duty six-fin radiator
■■●
Electric ether start aid
■■■
Engine coolant heater, 1,000 watts,
110 volts
■■■
Fuel/water separator*
■■■
Radiator sand screen (requires blower fan)
■■■
Reversible fan
■■■
Turbocharger
■ ●●
POWER TRAIN
Automatic spring-applied, hydraulic-
released park brake, lever operated
●●●
Cooler
●●●
Oil-to-air for torque converter
transmission
●●●
Primary and secondary service brakes
●●●
Transmission neutral lock with starter
safety switch
●●●
Winch drive with cover
●●●
Axle seal guards*
■■■
Direct drive transmission with oil-to-air
cooler, decelerator, declutch, and sus-
pended power control inching pedal
■■■
ELECTRICAL
Auto-reset circuit breakers
●●●
By-pass start safety cover at starter
●●●
Positive terminal battery covers
●●●
Single battery, 180-min. reserve capacity,
625 CCA
●●●
Auxiliary starting receptacle under hood
■■■
Dual batteries, 360-min. reserve capacity,
1,250 CCA
■■■
Master electrical disconnect switch,
lockable
■■■
HYDRAULIC SYSTEM
“O” ring face seal connectors
●●●
Fourth and/or fifth function valve (with
or without float) and levers for auxiliary
equipment*
■■■
Power-beyond valve for front/rear
auxiliary valves
■■■
Pump, 23 gpm, with hydraulic oil cooler
■■■
UNDERCARRIAGE
Front idler and sprocket bolt-on chain
guides
●●●
Full-length track frame covers
●●●
Bolt-on full-length track guards
■■■
Counterweights, front idler, 350 lb.
(158 kg) each
■■■
Counterweights, sprocket, 564 lb. (256 kg)
total
■■■
Full grouser track shoes, 16 in. (406 mm)
to 24 in. (610 mm), for direct drive
transmissions*
■■■
Closed and open center track shoes*
■■■
Rubber track pads*
■■■
Sealed and lubricated chain
■■■
LIGHTS
Two front driving/working and one rear
working halogen, 33,000 candlepower
(375 737 lux each)
■■■
OPERATOR’S STATION
Built-in Operator’s Manual storage
compartment and manual
●●●
Decelerator
●●●
Deluxe suspension vinyl seat
●●●
Adjustable armrests, thigh support,
backrest, height/weight, and fore-aft –
Conforms to SAE J899
Electronic monitor system with audible
and visual warning
●●●
Coolant temperature / Engine oil
pressure / Hydraulic filter restric-
tion / Low alternator voltage /
Transmission filter restriction /
Transmission pressure / Transmis-
sion temperature
Fuel gauge, electric, illuminated
●●●
Gauge/indicator package
■■■
Gauges, illuminated
Engine coolant temperature / Engine
oil pressure / Transmission oil
temperature
Indicator lights
Low alternator voltage / Trans-
mission oil filter restriction /
Transmission oil pressure
Horn, electric
●●●
Conforms to SAE J994, J1446
Hourmeter, electric, illuminated
●●●
Interior-mounted rearview mirror
●●●
Conforms to SAE J985
Key start switch with electric fuel shutoff
●●●
Modular design ROPS/FOPS canopy
●●●
Conforms to SAE J1040
Pedal steering
●●●
Seat belt, 2 in. (51 mm), with retractors
●●●
Conforms to SAE J386
Slip-resistant steps and ergonomically-
located handrails
●●●
Conform to SAE J185
Tool storage behind seat
●●●
Cab
■■■
Air conditioning, 33,000 Btu* / Deluxe
headliner / Dome light / Floormat /
Fresh air intake heater/defroster/
pressurizer, fresh air precleaner,
400 CFM, 40,000 Btu/hr (11.7 kW) –
Conforms to SAE J1503, J1535D /
Front and rear windshield wipers /
Front and rear windshield washers /
Interior-mounted rearview mirror /
Tinted safety glass / Conforms to
SAE J1040
Cab protection
■■■
Door screens* / Front screens* / Lexan
®
Margard
®
windows* / Limb risers* –
Arched or point-to-point with over-
head exhaust* / Rear screen / Side
screens
Dual lever dozer controls
■■■
Headliner for ROPS
■■■
Lever steering
■■■
Low-profile ROPS
■■■
Conforms to SAE J1040
Non-suspension vinyl seat
■■■
Adjustable armrests, backrest, and
fore-aft – Conforms to SAE J899
Radio, AM/FM weather band
■■■
ROPS protection, low profile
■■■
Door screens* / Front screens* / Limb
risers* – Arched or point-to-point
with overhead exhaust* / Rear screen /
Side screens
ROPS protection, standard height
■■■
Door screens* / Front screens* / Limb
risers* – Arched or point-to-point
with overhead exhaust* / Rear screen /
Side screens
ROPS-to-cab conversion panels*
■■■
Seat belt, 3 in. (76 mm), without retractors
■■■
Conforms to SAE J386
Steering conversion kits*
■■■
Suspension vinyl seat for backhoe use
■■■
Adjustable armrests, thigh support,
backrest, height/weight, and fore-
aft – Conforms to SAE J899
OVERALL VEHICLE
Perforated engine side shields
●●●
Reverse alarm
●●●
Switchable to 97 dB(A) or 111 dB(A) /
Conforms to SAE J994, J1446
Vandal protection
●●●
Engine access door / Fuel tank cap /
Hydraulic and transmission access
door / Instrument panel
Backhoe with 24-in. (610 mm) standard
bucket, 3,350 lb. (1522 kg)
■■■
Alternate stabilizer pads / Backhoe
bucket coupler / Backhoe mounts /
Extend
able dipperstick* / Hydraulic
and mechanical quick disconnects /
12–36-in. (305–914 mm) standard,
heavy-duty, and extra heavy-duty
buckets
Counterweights, rear, 300 lb. (136 kg)
each (five maximum)
■■■
Counterweights, with/without draw-
bars, 2 in. (51 mm) thick, 300 lb.
(136 kg) each
■■■
Extended drawbar with pin for pull-
type implements
■■■
Recommend rear screen
Fireplow*
■■■
Front tow hook
■■■
Heavy-duty grille screen
■■■
PTO*
■■■
Rigid drawbar with pin
■■■
Recommend rear screen
Ripper, parallelogram with five shank
pockets and three teeth, 1,380 lb.
(626 kg)
■■■
Ripper, radial with five shank pockets
and three teeth, 742 lb. (336 kg)
■
SMV emblem
■■■
Swinging drawbar*
■■■
Tachometer*
■■■
Three-point hitch, hydraulic actuated*
■■■
Winch, front*
■■■
Winch, rear, John Deere Model 4000,
1,190 lb. (540 kg) – Rear screen
required
■■■
Freespool function / Power in, power
out optional / Standard or low speed /
Compatible drawbar / Fair-lead,
four roller / Log arch*
450G 550G 650G 450G 550G 650G 450G 550G 650G
97-09 English version 2/25/00 8:55 AM Page 20
