INTRODUCTION
ank you for purchasing a new EOTECH magnier. ese
magniers oer users of the Holographic Weapon Sight (all
models) the additional advantage of vastly improved target rec-
ognition and increased lethality at medium range distances. e
STS mount allows the user the ability to engage the enemy with condence in a Close Quarters Battle (CQB)
situation or at distances out to 600 meters or more. is user manual describes the features of the EOTECH
Magniers and provides information on their use and maintenance. Please read the instructions carefully
before mounting and using the magnier. Always practice proper rearm safety.
OPTIC CONFIGURATION
e EOTECH Holographic Weapon Sight (HWS)
product line has two dierent heights above the rail
based on user preference. For this reason, the mag-
nier does not come preassembled to the mount.
It is user congurable based on the specic model
HWS it will be mounted behind. e 7mm riser,
included, may be required to align the magnier
optical axis with the sight. Only HWS models with
side buttons or quick detach levers require the use of
the riser. For all other HWS models, the riser should
not be used.
e magnier system can be congured to switch to the le or to the right based on shooting preference.
Typically, right handed shooters prefer the mount to switch to the right, and le handed shooters to the le.
To congure your HWS you will need a screwdriver (not included). If the riser is not used, the shorter screws
should be selected. e longer screws are used with the riser only. If the riser is being used, place the riser
on the optic mounting interface. Open the STS mount. Position the mount on the optic mount interface (or
riser) so it opens either to the le or right (based on preference). Insert each screw through the components,
and tighten securely. If using a torque wrench, the screws should be tightened to 24 in-lbs. Note: If you
purchased the magnier as part of an HHS combo kit, the screw pack will not be included as the magnifer
comes preassmbled.
USER’S MANUAL FOR G-SERIES
MAGNIFIERS
is product is controlled under the Export Administration Regulations (EAR) ECCN 0A987, and may not be exported to a
foreign person, either in the U.S. or abroad, without a license or exception from the U.S. Department of Commerce
For use with G Series Magniers or HHS
systems containing the Switch to Side
(STS) mount. Images will vary by model.
SPECIFICATIONS
- Water-Resistant: 33 . (10m)
- Sealing: Fog-resistant internal optics
- Finish: Non reective / Rubber coated
- Optical Axis Adjustment: Internal adjustment
- Switch Orientation: Ambidextrous mount
- Flip Orientation to allow le or right ip
- Rail Interface: 1” Weaver or MIL-STD-1913 with Quick Detach lock
Included
• Magnier • Switch to Side (STS) Mount• 7mm Riser • 4 Screws
BASIC OPERATION
e G-Series magniers are designed to be used behind an EOTECH Holographic Weapon Sight (HWS). e
magnier can be mounted directly behind the HWS. Simply switch the magnier out of the way and operate
the sight. When used with HWS models 518, 558, 556, 517, EXPS or 516 HWS (with side button interface) the
user can easily operate the sight even with the magnier in the locked position.
Positioning the Reticle:
Once the magnier is installed properly behind the HWS, it may be necessary to re-zero the sight. is may
be due to the shooter’s ability to see the target and Point of Impact (POI) more accurately than without the
magnier. Re-zeroing the sight will prevent a perceived shi in POI when going from no magnication to
magnication.
RETICLE POSITION ADJUSTMENTS
Aer zeroing or re-zeroing the sight, it may be necessary to reposition the reticle image into the center of the
magnier window. is is aesthetic in nature and has no aect on the sight’s zero. Turn the horizontal and
vertical adjustments on the top or side of
the magnier by hand, with a coin or a
at head screwdriver to reposition reticle
to the desired position.
SWITCH OPERATION
To switch the magnier to the side,
simply push the optic to the right or le,
depending on how it is mounted. To close
the mount, push the magnier back into
its original position until a hard stop is
achieved.
ADJUSTABLE DIOPTER
e optic includes an adjustable diopter that allows the user to customize the
focus to their particular vision. is feature ensures a crisp, clean aiming dot
for more precision and shot placement. To adjust, simply grasp the diopter
with the thumb and fore nger and turn either clockwise or counter-clockwise
until a clear sight picture is achieved.
Note: Depending on the users vision, you may observe a small change to the
magnication during diopter adjustment.
M1960 Rev A
Figure 1
Figure 2
Figure 3
MAINTENANCE
Maintenance of the magnier is limited to cleaning of the outside housing of the optic and cleaning the lenses.
e optical system is coated with anti-reection material. When cleaning the glass surfaces, rst blow away
any dirt and dust. Fingerprints and lubricants can be wiped o with lens tissue or a so cotton cloth which is
moistened with lens cleaning uid or glass cleaner, sold in any camera store. Never clean the glass surface with
a dry cloth or paper towel; always dampen the glass surfaces prior to cleaning.
No maintenance is needed on the magnier’s surface, except to occasionally wipe o with a so cloth. Use
only a water-based cleaner such as glass cleaner, ammonia, or soap and water. CAUTION: Never use any
solvent-type cleaner such as alcohol or acetone.
WARNING: NEVER DISASSEMBLE YOUR MAGNIFIER! e optical cavity is purged, nitrogen lled,
and sealed to achieve fog proof performance. Disassembly will void the warranty and damage the magnier.
If the switch action of the switch to Side mount begins to stick from wear, use a common spray lubricant on
the hinge portion of the mount. No other maintenance is needed on the Switch to Side Mount other than
cleaning the surface. Please follow the same guidelines when cleaning the magniers.
Figure 4
Figure 5
INSTALLATION
To install the congured magnier onto the weapon, open the quick detach lever. To do this, use your thumb
to depress the locking button (see Figure 4). Once depressed, swing the quick detach lever open and away
from its nested position. Place the mount in the desired position behind the HWS. Once the mount is located
in the desired position, push the magnier forward until the cross bolt of the magnier is set into the slot
located on the mount. Close the quick detach lever.
If the mount is too loose or tight for your specic rail, adjustments can be made for a proper t (see Figure
5). First, remove the magnier from the rail. Leaving the quick detach lever in its open position, turn the
unit upside down, exposing the rail interface. To loosen the adjustment, turn the dial counterclockwise. To
tighten, turn the dial clockwise. Once done, re-mount the optic to the rail. Continue incremental changes
until a desired t is achieved. CAUTION: Never make adjustments while the quick detach lever is in the
closed position.
THE EOTECH PRESTIGE WARRANTY
ank you for choosing EOTECH® for your new purchase. We understand your passion for shooting and
your reliance on products that will provide years of dependable use. at is why we oer a 10-year limited
EOTECH® Prestige Warranty*, as described below. Should you experience a problem with your EOTECH®
product, we will do the following to make it right for you.
With the EOTECH® Prestige Warranty, we warrant that your Holographic Weapon Sight or Magnier product
will be free from manufacturing defects in material and workmanship (including electronics) under normal
use for a period of ten (10) years from the later of (i) customer’s proof of the rst purchase of the new product
from an authorized commercial seller of EOTECH® products or from EOTECH® directly, or (ii) manufac-
turer’s date/serial number (as specied on the product). EOTECH® will, free of charge and as determined by
EOTECH®, either repair or replace your product with a comparable product for the rst ve (5) years. From
ve (5) to ten (10) years, EOTECH® will, at the customer’s request, evaluate and repair any and all defects in
material and workmanship for a seventy-nine dollar ($79.00 USD) bench fee. is warranty extends to subse-
quent owners to the remaining extent of the original owner’s warranty. We do this because we want you to be
as condent in your purchase as we are in the quality of our product.
THIS WARRANTY DOES NOT APPLY TO THE FOLLOWING:
1. Theft, loss, neglect or vandalism
2. Abuse, misuse, improper installation and modification, alterations, abnormal use, or accidents not result-
ing from a defect in material and workmanship under normal use of the product.
3. Cosmetic damage that does not affect the product’s use, operation or performance.
4. Any defect or damage caused by repairs or services not performed by EOTECH.
EOTECH® products to be repaired under this warranty, must have a valid return material authorization
(RMA) number; purchasers may obtain this number by submitting a Return Authorization Request Online at
www.eotechgear.com. If you do not have access to a computer, you may call EOTECH for assistance. Products
that arrive at EOTECH® without a valid Return Authorization Number will be returned to sender without
service. Once you receive the RMA number, send the product, postage prepaid, to EOTECH®. All product(s)
must be fully insured and have the correct postage; EOTECH® will not be responsible for improper postage or
missing/damaged merchandise during shipment. International repairs may include additional shipping and
handling charges.
THE WARRANTY PROVIDED HEREIN SHALL BE THE SOLE AND EXCLUSIVE WARRANTY. THERE SHALL BE NO OTHER WARRAN-
TIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OR ANY OTHER OBLIGATION ON THE PART OF EOTECH WITH RESPECT TO THIS WARRANTY. THIS WARRANTY DOES
NOT AFFECT ANY STATUTORY WARRANTY RIGHTS THE CONSUMER MAY HAVE AGAINST THE SELLER OF THIS PRODUCT.
EOTECH SHALL HAVE NO LIABILITY FOR ANY DAMAGES OR FUTILE EXPENSES OF WHATEVER NATURE (WHETHER DIRECT; IN-
DIRECT; INCIDENTIAL; CONSEQUENTIAL; SPECIAL OR OTHER DAMAGES) UNDER THIS WARRANTY. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM JURISDICTION TO JURISDICTION. SOME
JURISDICTIONS DO NOT ALLOW EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
* is warranty applies to new purchases of Holographic Weapon Sight or Magnier products and retroactively applies to Holographic Weapon
Sight or Magnier products sold in 2017 by an authorized commercial seller of EOTECH® products or from EOTECH® directly.
FACTORY CONTACTS
Web....................... ..............................................................................................................https://www.eotechgear.com
Customer Service/Repair........................................................................................................................888-EOTHOLO
(734) 741-8868
Shipping Address: EOTECH® 1201 E. Ellsworth Rd. Ann Arbor, MI 48108 USA
EOTECH DISCLAIMERS AND NOTICES
• EOTECH reserves the right to change the product specications at any time.
• All EOTECH material is for information purposes only and does not constitute any binding obligation
or agreement by EOTECH, and all claims about performance characteristics assume normal, responsible
usage within the warranty period.
